Completely prevent warping with the new Fialform bed adhesive spray designed specifically for high temp materials PETG, ABS, ASA, nylon and many more FDM based materials or when you are having issues getting the first layer to print. The part is securely held whilst the plate is warm and automatically pops off when the printer has cooled making it the ideal solution for bed adhesion. Filaform Bed adhesive spray EXTRA STRENGTH has been tested on smooth and textured PEI bed platforms and works very well in both scenarios.
In the world of 3D printing, bed adhesion is a crucial factor that can make or break the success of a print. If your prints aren't sticking to the bed, you'll end up with incomplete or distorted prints that are unusable. That's where Filaform Bed Adhesive Spray Extra Strong comes in. This high-performance bed adhesive is specifically designed to hold your 3D prints in place, even during prolonged printing sessions. Made from a specially formulated blend of polymers, this adhesive creates a strong, durable bond that will keep your prints in place, specifically designed for high-temperature filaments.
Applying Filaform Bed Adhesive Spray Extra Strong is easy. Simply shake the bottle well and spray a thin layer onto your bed. Allow it to dry for a few minutes before printing. It's suitable for use with a wide range of high-temp 3D printing materials, including PETG, ABS, PC, PEEK and carbon fibre nylon. Its versatility makes it an excellent choice for any 3D printing enthusiast looking to improve the quality of their prints.
When it comes to removing your printed parts, Filaform Bed Adhesive Spray Extra Strong makes it easy. Simply allow the bed to cool and your printed parts will self-release without needing a scraper. This feature makes it a breeze to remove your parts and get them ready for post-processing.
Filaform Bed Adhesive Spray Extra Strong is an excellent choice for anyone looking to improve the quality of their 3D prints. Its strong, durable bond and easy application make it a must-have for any 3D printing enthusiast. Order yours today and take the first step towards consistent, high-quality prints every time.
Instructions:
- Ensure the print surface is clean
- Spray thoroughly onto the print base from approximately 10cm ensuring you cover the entire surface
- Print your model
- Wait for the platform to cool down (below 30 degrees C) and the part should remove automatically.
3D Printer Bed Adhesive Extra Strength
Customer Reviews
4.0
8 reviews
Verified purchases only.
Powered by Bazaarvoice.
Sticky wickets have nothing on this stuff
Went into the Fyshwick store and happened to mention that I was having bed adhesion issues with my dabbling in ASA. Even following all the "rules", it was pretty hard to to stop anything ASA turning into the ABC logo and rolling into the bottom of the chamber. Rohan quickly went through my settings with me, then recommended this bed adhesive. Gave it a try that evening and WOW, this stuff _sticks_. Like, really sticks. I don't doubt that some have damaged their bed coatings by impatiently removing prints while the bed is still hot. Go easy with this stuff (and maybe give it a miss if you're doing PLA or PETG) and you should get great results. Cheers to Rohan and the team at the Fyshwick store.
Excellent
I found this adhesive to be excellent. Dont be put off by "oldmates" review. I dont see how any glue could damage the bed - so I think it may have been user error... I did three large prints using eSun eASA and they adhered to the build plate perfectly. Cleanup was jus warm water and little detergent.
0 failed prints
Works great every time and the bed is fine. Washes away very easily under warm water.
Sticks like stuff to a blanket!
Have printed one ASA print on the ceramic side of my Ender3 V2 glass bed. It kept the print down very well. It did pull a piece of the ceramic surface away from the glass sheet even though the bed was at ambient temp at tome of removal. Have turned the glass over and will print on glass only and see how it goes for a second ASA print. Amazing stuff, just needs the lightest of sprays on to the bed.
Useless on Nylon
I'd give it 0 stars if I could based on 2 attempts with nylon on a textured PEI bed - Maybe it'll work on other filaments but with nylon it's totally useless - tried diff bed temps - failed to hold both times - a simple 50x50 square - broke loose on layer 2 or 3 both times - Went back to Elmer's Glue - worked fine - try it if you're keen - not me
Works
This stuff is superb, no failed prints since using it
Unbeatable
Sicks better than anything else can’t get off a brim without soaking the pei sheet
Garbage destroys beds
Will destroy your bed , DO NOT USE THIS AT ALL!!!!